Furnace Repair Quincy MA — Same-Day Heating Service for Gas & Oil Systems

Furnace Repair & Heating Service in Quincy MA — Wollaston · North Quincy · Adams Shore · Squantum · Merrymount · Germantown · All ZIP codes 02169 · 02170 · 02171

100+ Reviews Trusted by local homeowners
Licensed MA HVAC Contractor Licensed & insured service
Same-Day Appointments Same-day appointments available
FURNACE TROUBLESHOOTING

Furnace Repair Quincy MA What to Check Before You Call

Run through this in two minutes. It resolves roughly 10% of no heat calls without a service visit.

01

Gas furnace not turning on

Check the thermostat and confirm it’s set to “Heat” and the temperature setpoint is above the current room temperature. Check whether the furnace power switch, which looks like a light switch and is usually on the wall near the unit, is on. Check the circuit breaker labeled “furnace” or “air handler.” Check the furnace filter. A severely clogged filter triggers a high limit safety switch that shuts the system down.

02

Oil furnace not firing

Check your oil tank gauge. Running out of fuel is more common than most homeowners admit, especially early in the season. Press the red reset button on the burner assembly once only. If it locks out again within a few minutes, do not press it a second time. Repeated resets flood the combustion chamber with unburned oil, creating a hazardous condition.

03

Pilot light issues

If your furnace has a standing pilot light and it’s out, check the manufacturer instructions on the unit door panel for the relighting procedure. If it won’t stay lit after following the procedure, the thermocouple has likely failed. A typical repair costs $75 to $150.

If none of the above applies Call (617) 928 8469. Everything after that is our job, done safely by a licensed technician.

Call Furnace Repair
HVAC technician inspecting a residential furnace in Quincy MA
Professional furnace inspection and diagnostic service
LOCAL FURNACE SERVICE

Who We Help

Quincy homeowners who woke up to a cold house on a January morning

Adams Shore and Squantum oil heat customers with burners that won’t fire or lock out repeatedly

North Quincy condo owners whose forced air system stopped producing heat

Landlords with tenants reporting no heat, a Massachusetts legal requirement from September 15 through June 15

Homeowners who’ve had a furnace “repaired” twice in two years and are tired of paying for band aids

Landlord or Property Manager?

No heat in a Massachusetts rental is a legal violation, not just an inconvenience. We prioritize heating calls for rental properties and provide written documentation for your records.

✓ Priority Rental Calls ✓ Written Service Documentation ✓ Same Day Availability
Licensed & insured in Massachusetts 24/7 emergency HVAC service Mass Save certified contractor Serving ZIP codes 02169, 02170, 02171
QUINCY HEATING CONDITIONS

Quincy’s Heating Reality Why Furnace Problems Are Different Here

Quincy’s heating market is not like the suburbs west of Boston. It is shaped by three things that most HVAC companies rolling through the South Shore on a broad service route don’t fully account for.

01

Aging Housing Stock with Aging Systems

Over 37% of Quincy’s homes were built before 1940. Those homes were built around cast iron radiators and oil or gas boilers, not forced air furnaces. But decades of renovations have introduced forced air systems into buildings that weren’t designed for them, often with compromised duct layouts, undersized returns, and original electrical panels. Diagnosing heating problems in these homes requires understanding the building’s history, not just the equipment.

02

High Oil Heat Dependency in Coastal Neighborhoods

Adams Shore, Squantum, Houghs Neck, and parts of Germantown still have a significant percentage of homes on oil heat. Older Beckett or Riello oil burners are paired with steam or hot water systems. Oil system service requires specific equipment and knowledge that gas focused HVAC companies frequently lack. We service both.

03

Boiler vs. Furnace Distinction

Many Quincy homeowners use the terms interchangeably, but they’re different systems that fail differently. A furnace heats air and distributes it through ducts. A boiler heats water and distributes it through radiators or baseboards. This page covers furnace repair. If you have radiators and a basement boiler, which is common in Wollaston, Adams Shore, and Quincy Center, call us directly and we’ll confirm what you have and whether we’re the right call.

SYSTEM TYPES

Furnace Types We Repair in Quincy MA

01

Gas Furnaces

The most common forced air heating system in Quincy’s post 1960s homes and converted older buildings. We service all major gas furnace brands including Carrier, Trane, Lennox, Goodman, Rheem, York, Bryant, and American Standard. We work on single stage, two stage, and modulating systems across all efficiency levels from standard 80% AFUE to high efficiency 96%+ condensing furnaces.

02

Oil Furnaces & Oil Burners

Common in Adams Shore, Squantum, Houghs Neck, and older sections of Germantown and West Quincy. We service Beckett, Riello, and Carlin oil burners paired with warm air furnaces. Oil system service includes nozzle replacement, electrode cleaning and gap setting, combustion analysis, heat exchanger inspection, and fuel filter replacement.

03

Electric Furnaces

Less common but present in some Quincy condos and apartments without gas access. We diagnose and repair electric furnaces, including sequencer failures, heating element replacement, and control board issues.

04

Heat Pump Systems in Heating Mode

If your home uses a heat pump mini split or a ducted heat pump, we diagnose and repair heating mode failures as part of our complete heat pump repair service.

FURNACE DIAGNOSTICS

Common Furnace Problems We Fix in Quincy

No Heat Furnace Not Starting

Most common in November and December when systems come back from months of sitting idle. Cause is usually a failed igniter, hot surface ignitor, $150 to $250 repair, a faulty flame sensor coated with oxidation, $85 to $150 to clean or replace, or a failed inducer motor that prevents the system from establishing draft before ignition.

Furnace Short Cycling Turns On and Off Every Few Minutes

The system fires, runs briefly, then shuts down. Over and over. Short cycling is typically a safety response to overheating caused by a clogged filter blocking airflow, a failing heat exchanger causing abnormal temperatures, or a faulty high limit switch reading incorrectly.

The heat exchanger cause is the one to take seriously. A cracked heat exchanger allows combustion gases, including carbon monoxide, to enter the airstream.

Furnace Running but No Heat Reaching the Rooms

The burner fires, the blower runs, but the air coming from the vents is room temperature or barely warm. Common causes include a blower motor running in reverse after a recent repair, a failed heating element in an electric furnace, or a gas valve that’s stuck partially open and sending insufficient fuel to the burner.

Loud Noises From the Furnace

  • Banging on startup: Delayed ignition. Gas builds up before firing. Carbon and sulfur deposits on the burner need cleaning. Address immediately.
  • Squealing: Blower motor bearing failure. The motor is on its way out.
  • Rumbling during burner operation: Dirty burners, incorrect air fuel mixture, or a partially blocked heat exchanger.
  • Metal on metal scraping: The blower wheel has come loose and is hitting the housing. Shut the system down and call.

Yellow or Orange Flame Instead of Blue

A gas furnace flame should be steady and blue with a small blue orange tip. A predominantly yellow or orange flame indicates incomplete combustion, often from a dirty burner or an incorrect air fuel ratio. It also indicates a higher likelihood of carbon monoxide production. This is a service call, not a wait and see situation.

SAFETY

Carbon Monoxide Detector Triggering

Evacuate first. Open windows, leave the building, and call 911. After the fire department has cleared the building, call us to inspect and service the furnace before it is used again. A cracked heat exchanger is the leading furnace related cause of carbon monoxide in Quincy homes.

HVAC technician servicing an oil furnace burner
Oil furnace burner inspection and repair
REPAIR OR REPLACE

Furnace Repair vs. Furnace Replacement The Honest Calculation

The $5,000 rule applies to heating systems the same way it applies to AC. Multiply the repair cost by the age of the system in years. Over $5,000 replacement math usually wins. Under $5,000, repair.

But furnace replacement has a dimension AC replacement doesn’t. The Mass Save heat pump opportunity. If your furnace is at or past end of life, gas furnaces typically last 15 to 20 years and oil furnaces 15 to 25 years with proper service. Replacing it with a heat pump system rather than another furnace may qualify for Mass Save incentives.

For Quincy homeowners on oil heat in particular, the math looks like this.

Scenario Estimated Cost
Oil Furnace Repair (Major) $800 to $1,800
Oil Furnace Replacement (New Oil) $4,500 to $7,500 Installed
Heat Pump Installation (Gross) $10,000 to $18,000
Mass Save Heat Pump Rebate Potential incentive varies
Heat Pump Net Cost Depends on system and eligibility
Annual Oil Heat Savings Varies by home and fuel usage

A homeowner on Adams Shore spending heavily on heating oil may find that a heat pump becomes more attractive when rebates and long term operating costs are included. We can run the repair versus replacement numbers before you make a decision.

OUR PROCESS

Our Furnace Repair Process in Quincy MA

1

Call Triage 5 Minutes

You describe what’s happening, no heat, short cycling, strange noise, or an error code on the display. We confirm your fuel type, gas or oil, system type, and Quincy neighborhood. We tell you whether it’s a same day or next day visit and explain the diagnostic cost.

2

Full System Diagnostic

The technician inspects the heat exchanger, burner assembly and flame quality, igniter and flame sensor, inducer motor and pressure switches, blower motor and capacitor, filter condition, gas valve or oil burner components, flue pipe, venting, thermostat, and control board. We measure combustion efficiency with appropriate diagnostic equipment.

3

Written Estimate Before Work Starts

Parts, labor, and total cost are provided before any repair begins. You approve it or you don’t. If you decline, you only pay the diagnostic fee. No verbal quotes that change on the final invoice.

4

Same Visit Repair

Igniters, flame sensors, capacitors, pressure switches, thermocouples, oil burner nozzles, and electrodes are common service parts. Most straightforward furnace repairs can be completed during the first visit when the required part is available.

5

Post Repair Safety Check and Explanation

After the repair, we run the system through a complete heating cycle, verify proper operation, check combustion and venting where applicable, and explain what failed, why it happened, and what to watch for.

HVAC technician performing a furnace diagnostic inspection
Furnace diagnostic testing and professional HVAC service
REAL QUINCY SERVICE

Real Job, Real Result Before & After

CASE STUDY 01

Oil Furnace Lockout Adams Shore Triple Decker, January

The Situation

A homeowner on Sea Street in Adams Shore called at 7:15am on a January morning. No heat. The oil furnace, a Beckett burner forced air system from 2008, had locked out overnight. The homeowner had pressed the reset button twice before calling. Indoor temperature: 54°F. Two elderly tenants were living in the upper units.

Before

At arrival the technician found a heavily fouled nozzle and coked electrodes from a summer of sitting idle. The nozzle was delivering fuel at an incorrect spray angle, causing intermittent ignition failure. The cad cell sensor was reading incorrectly because of soot accumulation, triggering the safety lockout. The oil filter had not been changed in at least two seasons based on its condition.

What We Did

We replaced the nozzle and oil filter, cleaned and regapped the electrodes, cleaned the cad cell, ran combustion analysis, and completed a full burner tune up. The written estimate before work began was $285 for parts and labor. The system fired cleanly on the first startup after service.

After

Full heat was restored the same morning. The heat exchanger was inspected and confirmed intact. Indoor temperature recovered to a comfortable level. The homeowner also scheduled annual oil burner maintenance for the following season.

Total Cost $285

A service call delayed for two seasons resulted in a January emergency and a home that dropped to 54°F. Preventive maintenance can help reduce the chance of similar breakdowns.

CASE STUDY 02

Gas Furnace Short Cycling North Quincy Condo, February

The Situation

A homeowner in a North Quincy condo building called in mid February. Their 9 year old Carrier gas furnace was short cycling, firing for 3 to 4 minutes, shutting off, then trying again every 8 to 10 minutes. The home was hovering around 61°F despite the thermostat being set to 70°F.

Before

System testing showed the furnace was not completing normal heating cycles. Pressure switch operation and inducer performance were investigated along with airflow, thermostat operation, and the furnace control sequence.

What We Did

The affected components were serviced and the furnace sequence was tested again. The system was allowed to complete an extended heating cycle before the repair was considered complete.

After

The furnace completed a continuous heating cycle without the previous short cycling behavior. The homeowner was also given a maintenance recommendation and information about the system’s future service needs.

Previous Repair Costs $680
Repair Cost $340
Heating Performance 70°F
System Status Short Cycling Resolved
Future Recommendation Monitor System

Has your furnace been “repaired” more than once but the same problem keeps coming back? The issue may be the diagnosis, not the parts. Complete system testing helps identify the actual fault before recommending a repair.

Flat fee diagnostic • Written estimate before work begins • Same day service available when scheduling allows
2026 SERVICE PRICING

Furnace Repair Pricing in Quincy MA

Typical service ranges vary by system, diagnosis, parts, and labor.

Repair Typical Cost
Diagnostic / Service Call $85 to $125
Igniter Replacement $150 to $250
Flame Sensor Cleaning / Replacement $85 to $150
Thermocouple Replacement $75 to $150
Pressure Switch Replacement $125 to $225
Inducer Motor Replacement $350 to $650
Blower Motor Replacement $350 to $600
Gas Valve Replacement $300 to $550
Control Board Replacement $400 to $750
Oil Burner Nozzle + Tune Up $150 to $285
Heat Exchanger Replacement $1,200 to $2,400
Annual Furnace Tune Up $125 to $175
Emergency / After Hours Diagnostic $145 to $175

Written estimates before work starts. At the point where repair cost becomes substantial, we can compare the repair against replacement and available heating incentives.

QUICK REFERENCE

Furnace Repair vs. Replacement Quick Reference

System Age Repair Cost Recommendation
Under 10 Years Under $800 Repair. The system may still have significant service life remaining.
10 to 15 Years Under $600 Repair and maintain annually.
10 to 15 Years Over $600 Compare repair cost with replacement options.
15 to 20 Years Over $500 Replacement may make more financial sense.
Over 20 Years Any significant repair Consider replacement.
Any Age Cracked heat exchanger Address immediately. A cracked heat exchanger can create a carbon monoxide safety risk.
LOCAL CUSTOMER FEEDBACK

What Quincy Homeowners Say About Our Furnace Repair Quincy

★★★★★
Oil furnace locked out on a January morning with tenants in the building. They were there quickly and diagnosed the issue instead of guessing.
Paul K. Adams Shore
★★★★★
Had another company out twice for the same short cycling problem. These guys actually tested the system and found the issue.
Michelle R. North Quincy
★★★★★
Professional, honest, and thorough. They explained the furnace problem clearly and showed me what needed attention.
Gary T. Merrymount
FURNACE REPAIR QUINCY MA

Furnace Not Heating? Call (617) 928 8469

Tell us what your furnace is doing, what type of system you have, and where you are located in Quincy. We’ll help determine the next step.

Licensed & insured • Furnace diagnostics • Gas & oil systems • Quincy MA
FURNACE REPAIR QUINCY MA

Got Questions?

We’re happy to help. If you can’t find the info you’re looking for, please don’t hesitate to reach out to us!

Call us (617) 928-8469
How fast can you get to Quincy for furnace repair?

For heating emergencies (no heat, Massachusetts winter) our target is the same as cooling season 2–4 hours from your call. For same-day non-emergency service, we typically have morning and afternoon availability most weekdays. We confirm a two-hour arrival window and text when the technician is on the way.

Is no heat in a rental property a legal issue in Massachusetts?

Yes. Massachusetts law requires landlords to maintain indoor temperatures of at least 68°F between 7am and 11pm, and at least 64°F at all other times, from September 15 through June 15. Failure to provide adequate heat is a violation of the state sanitary code. We carry itemized written documentation of every service call useful for both tenant communications and municipal housing inspectors.

Do you service oil furnaces in Quincy?

Yes. Oil furnace service including Beckett and Riello burner tune-ups, nozzle replacement, combustion analysis, and heat exchanger inspection is a regular part of our work in Adams Shore, Squantum, Houghs Neck, and Germantown. We carry oil service components on the truck.

Contact us → to confirm scheduling for oil system work.

My furnace keeps locking out and I keep pressing reset. Is that OK?

No. The reset button exists for one-time use after a single lockout. If the system locks out again after a reset, pressing it again floods the combustion chamber with unburned oil or creates repeated failed ignition attempts on a gas system. Both create hazardous conditions.

One reset then call us.
What is the lifespan of a furnace in Quincy MA?

Gas furnaces typically last 15–20 years with proper annual maintenance. Oil furnaces last 15–25 years they’re built more robustly but require more consistent maintenance to reach the upper end of that range.

Both types in Quincy’s coastal neighborhoods last toward the lower end of their range due to humidity effects on the heat exchanger and flue components. Annual service is the single biggest factor in reaching the top of the lifespan range.

Should I repair my old oil furnace or switch to a heat pump?

If the oil furnace is under 15 years old and the repair is under $600, repair it. If it’s over 15 years old or the repair is significant, the heat pump math in 2026 is compelling up to $8,500 in Mass Save rebates makes the switch financially competitive with a straight oil furnace replacement while eliminating ongoing fuel costs.

We run the specific numbers for your home at the diagnostic visit.

Need Furnace Repair in Quincy?

Call now to schedule furnace service with a licensed Massachusetts HVAC technician.

Call (617) 928-8469

Need Furnace Help Today?

Whether your furnace has stopped working, keeps short cycling, or is making unusual noises, call us for professional furnace service in Quincy MA.

✓ Licensed & Insured ✓ Same Day Service ✓ Written Pricing ✓ Quincy Service Area